This one caused me some grief for the last few weeks, thought I’d share in case it helps anyone else…
Firefox is my prefered browser on Mac, it’s setup with all my passwords, bookmarks, extensions etc and I use Chrome for work, so when it stopped loading and started crashing for no good reason it was VERY annoying. Couldn’t find any cure for it, little mention of issues and nothing more helpful than the usual: update it, restart, disable extensions, clear your profile, reinstall etc etc.
The issue being that Firefox would hang on startup – nothing would load, not even the basic home page, and I had to force-restart the browser on a regular basis until it would eventually decide to work like nomal again…. ARGH!
The solution to my issue was to disable support for HTTP3. That’s very easily done and has completely fixed things on my Mac (in this case it’s an iMac Retina 5k, 27-inch with macOS Monterey).
Here’s how – it takes 5 seconds + a restart.
enter “about:config” in the address bar and then hit the “Accept the Risk and Continue” button…
filter the settings for “http3” via the search bar, click on the bottom right icon seen in this pic to change the value from true to false:
so that it loks like this:
then just restart the browser and if you had the same issue as me, it should now be sorted! Happy surfing.
Update: There is a some more detailed info here: https://bugzilla.mozilla.org/show_bug.cgi?id=1749908 incluing reports that disabling all of the data collection features may solve this (without the HTTP3 disabling update). Looks like this has been around for a while but only started affecting me a couple of weeks ago, and was hard to debug as there’s no obvious/searchable error message.
I bought an “Optoma H181x Full 3D HD Projector” back in 2015, and it’s been awesome for 7 years. No issues at all, just many happy hours of HD and 3D movie & TV watching.
Recently though, it started to overheat and switch itself off after just a couple of minutes running, with the ominous message “Fan locked. Projector will switch off automatically. Please contact service centre for repair“.
Looking around online I could see it was a common problem in older projectors, usually due to dust buildup, and sorted by either cleaning or replacing the fan.
I tried to clean the fan but it wasn’t very dirty and made no difference. Looking through the front vents with a torch, I could see the fan was trying to turn on startup, then giving up. It’s a pretty ordinary component but taking the projector apart sounded dangerous (many reports of this going badly for others) and after a partial attempt I decided it wasn’t something I was comfortable or confident doing…. too many hidden clips and other fragile parts needing disconnected or removed, like the IR receiver, the switches, the zoom/focus wheel, etc.
This pic shows the top panel removed (just one captive screw on the left of the cover needs undone, then it slides left and lifts up & off easily.). Note: there’s a sensor that prevents the projector from powering on while this cover is removed.
You can see the culprit fan lurking behind that yellow tape, it cools the bulb housing. To get anywhere near it I had to disconnect the wires via the plastic molex/clip on the left, remove those three screws on the far right, then carefully lift the bulb housing out (straight upwards), using the little metal handle with one hand and guiding the heat shields/flaps past the top of the cover with the other.
With that out of the way you can now see one side of the fan, but you can’t remove it from this side – here’s a close up pic:
I noticed the fan blades were stiffer and harder to rotate (by hand) than they probably should be, and I knew fans like these could sometimes be cleaned and lubricated… this sounded worth a shot (given the age and cost of repair, it was looking quite like ‘new projector time’ otherwise), but that cover was stuck down fast….
This pic shows the same side of the fan after I scraped off the cover to reveal four small holes. I then carefully placed 2-3 drops of ordinary multi-purpose oil in each hole. I let the projector stand in this position for a while, so the oil could work its way in/down, then cleaned the surface with Isopropyl Alcohol to remove any excess oil, before sticking some insulating tape back where the original label/cover had been. My projector sits up high and points downwards and I didn’t want any oil escaping…. or dripping on to the lamp!
I replaced the lamp housing and the cover and gave it a whirl – it’s now starting up first time no problem and running smoothly and quietly, just like it used to!
I think the placement of the fan – especially when the projector points downwards – means the fans central bearing is exposed to a lot of heat, which dries it out over time. It’s given many hours of use over the past 7 years so I’m not complaining, and hopefully I’ll get some more use out of it now.
This all took me quite a while to figure out and think through, but the actual fix was really easy and took about 10 minutes.
I thought I’d share this for anyone else facing the same issue.
